Bookmark and Share

Notice: On April 23, 2014, Statalist moved from an email list to a forum, based at statalist.org.


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

st: RE: RE: IV Command and Reported Results Problem


From   Sinan Hastorun <[email protected]>
To   "[email protected]" <[email protected]>
Subject   st: RE: RE: IV Command and Reported Results Problem
Date   Wed, 16 Feb 2011 14:14:56 -0500

Nick, I am only trying to figure out why I am unable to get these 3 values reported once I run ivregress. I did not imply in any way that theirs or anybody else's programs are to blame for the omission. I am seeking to find out what may be wrong with my model specification or the command line as I've written it. Why would this be a strange question? Stata users post questions about their problems all the time when they get what seem to be unexpected results or in my case, no values reported for certain measures. 

My model contains 51 dummy variables, one for each region represented, that is why the number of explanatory variables appear as 53. So my command is as follows for ivregress:

ivregress 2sls y i1 i2 i3 i4 i5 i6 i7 i8 i9 i10 i11 i12 i13 i14 i15 i16 i17 i18 i19 i20 i21 i22 i23 i24 i25 i26 i27 i28 i29 i30 i31 i32 i33 i34 i35 i36 i37 i38 i39 i40 i41 i42 i43 i44 i45 i46 i47 i48 i49 i50 i51 (x1 x2 = v1 v2 v3 v4 v5 v6), first noconstant

Finally, ivreg2 gives me the R-squared when I use a similar command structure.
 

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Nick Cox
Sent: Wednesday, February 16, 2011 1:17 PM
To: '[email protected]'
Subject: st: RE: IV Command and Reported Results Problem

It's a strange question to send to Statalist. Two out of three of the very distinguished authors of -ivreg2- are active on this list, and you seem to be asking: I get puzzling and disappointing results. Is your program to blame? 

What do you expect them to say? 

My only guess is that you are trying to fit a model that is too complicated or otherwise unsuitable for your data. As Maarten Buis often advises, retreat to a much simpler model, complicate slowly, and see when and where problems start biting.

But I am not an econometrician. The IV people on this list are better placed to advise, if only on what you should be telling them that you are not. 

Nick 
[email protected] 

Sinan Hastorun

Thank you Nick. I just included that note in my question in order to inquire about whether the command may be part of the problem here. Do you have a take on why I am not getting any actual numerical results reported for Wald chi2(53), Prob > chi2, R-squared?

Nick Cox

Short answer is No; no such simplistic statement deserves assent. 

Enormously longer answers from the experts....

Sinan Hastorun

I am running IV in STATA by using the command ivregress because it is said to perform better than ivreg or ivreg2. Is that correct?


*
*   For searches and help try:
*   http://www.stata.com/help.cgi?search
*   http://www.stata.com/support/statalist/faq
*   http://www.ats.ucla.edu/stat/stata/

*
*   For searches and help try:
*   http://www.stata.com/help.cgi?search
*   http://www.stata.com/support/statalist/faq
*   http://www.ats.ucla.edu/stat/stata/


© Copyright 1996–2018 StataCorp LLC   |   Terms of use   |   Privacy   |   Contact us   |   Site index