Statalist The Stata Listserver


[Date Prev][Date Next][Thread Prev][Thread Next][Date index][Thread index]

Re: st: RE: Problems with Outreg not being able to open a file--r(603)


From   "Joe McCrary" <[email protected]>
To   [email protected]
Subject   Re: st: RE: Problems with Outreg not being able to open a file--r(603)
Date   Wed, 15 Mar 2006 10:40:45 -0500

That was not a problem. I never opened the file. It was all part of
one larger do file.

On 3/15/06, Herman van de Werfhorst <[email protected]> wrote:
> Sorry to disturb again, but the message that the txt file of the outreg table could not be opened may point to the fact that this txt file is open. If the txt file is open you will definitely get that same message.
>
> Herman
>
> -----Original Message-----
> From: [email protected]
> [mailto:[email protected]]On Behalf Of Joe McCrary
> Sent: 15 March 2006 15:04
> To: Statalist
> Subject: st: Problems with Outreg not being able to open a file--r(603)
>
>
> I am running a series of 8 regressions, the results of which I'd like
> to append into a table using outreg. When I run it, I get the message
> that the file could not be opened after I try to append my 5th column.
> When I go to the directory where the results were being saved, the
> file is gone.
>
> What I did do to get it to work was write the results from the last 4
> regressions into a separate file. And it works fine when I do this.
>
> It seems to me that outreg is limited to 4 columns. Is this true?
>
> Here are the results from the 4th regression:
>
> . reg r8mssallch r8mssall03 ses04 swp04_pct
>
>       Source |       SS       df       MS              Number of obs =      51
> -------------+------------------------------           F(  3,    47) =    1.86
>        Model |  15.3237824     3  5.10792747           Prob > F      =  0.1498
>     Residual |  129.282356    47  2.75068842           R-squared     =  0.1060
> -------------+------------------------------           Adj R-squared =  0.0489
>        Total |  144.606138    50  2.89212276           Root MSE      =  1.6585
>
> ------------------------------------------------------------------------------
>   r8mssallch |      Coef.   Std. Err.      t    P>|t|     [95% Conf. Interval]
> -------------+----------------------------------------------------------------
>   r8mssall03 |  -.0388096   .0493324    -0.79   0.435    -.1380535    .0604344
>        ses04 |   .6325206   .3268157     1.94   0.059    -.0249478    1.289989
>    swp04_pct |   -.014927   .0195971    -0.76   0.450    -.0543513    .0244973
>        _cons |   9.807167   13.28449     0.74   0.464    -16.91779    36.53212
> ------------------------------------------------------------------------------
>
>
> . outreg using c:\Data\NAEP\all.txt, bdec(1) rdec(3) sigsymb(*,**,+)
> 10pct coefastr ctitle(R8ch) append
>
> But after the 5th regression:
>
>
> . //Math Grade 4
> . reg m4mssall05 m4mssall03 ses04 swp04_pct
>
>       Source |       SS       df       MS              Number of obs =      51
> -------------+------------------------------           F(  3,    47) =  244.64
>        Model |  2108.09966     3  702.699888           Prob > F      =  0.0000
>     Residual |  135.001742    47  2.87237748           R-squared     =  0.9398
> -------------+------------------------------           Adj R-squared =  0.9360
>        Total |  2243.10141    50  44.8620281           Root MSE      =  1.6948
>
> ------------------------------------------------------------------------------
>   m4mssall05 |      Coef.   Std. Err.      t    P>|t|     [95% Conf. Interval]
> -------------+----------------------------------------------------------------
>   m4mssall03 |   .9802351   .0507804    19.30   0.000     .8780781    1.082392
>        ses04 |   .5027639   .3406936     1.48   0.147    -.1826233    1.188151
>    swp04_pct |   .0309728   .0197241     1.57   0.123     -.008707    .0706526
>        _cons |     6.9462   12.21047     0.57   0.572    -17.61809    31.51049
> ------------------------------------------------------------------------------
>
>
> . outreg using c:\Data\NAEP\all.txt, bdec(1) rdec(3) sigsymb(*,**,+)
> 10pct coefastr ctitle(M4) append
> file c:\Data\NAEP\all.txt could not be opened
> r(603);
>
>
>
>
> --
> Joe McCrary
> **********************
>
> "No problem can be solved from the same level of consciousness that created it."
> --Albert Einstein
>
> *
> *   For searches and help try:
> *   http://www.stata.com/support/faqs/res/findit.html
> *   http://www.stata.com/support/statalist/faq
> *   http://www.ats.ucla.edu/stat/stata/
>
> *
> *   For searches and help try:
> *   http://www.stata.com/support/faqs/res/findit.html
> *   http://www.stata.com/support/statalist/faq
> *   http://www.ats.ucla.edu/stat/stata/
>



--
Joe McCrary
**********************

"No problem can be solved from the same level of consciousness that created it."
--Albert Einstein

*
*   For searches and help try:
*   http://www.stata.com/support/faqs/res/findit.html
*   http://www.stata.com/support/statalist/faq
*   http://www.ats.ucla.edu/stat/stata/



© Copyright 1996–2024 StataCorp LLC   |   Terms of use   |   Privacy   |   Contact us   |   What's new   |   Site index