Bookmark and Share

Notice: On April 23, 2014, Statalist moved from an email list to a forum, based at statalist.org.


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: st: foreach command


From   Caliph Omar Moumin <[email protected]>
To   "[email protected]" <[email protected]>
Subject   Re: st: foreach command
Date   Tue, 22 May 2012 15:06:09 -0700 (PDT)

Thank you both.
Ronan´s suggestion executed with labeling 1, 2, ....11 in each regression, but i could´t do Nick´s suggestion (it says invalid syntax), I would prefer if it gives the label names of each value which are `Disease names`.

I am not an expert in using the stata, i thought the idea of looping was to make more flexible and short. 

Anyway i guess it is enough to figured out which subchapter each regression belongs. 
Thank you both again 
 
Kind Regards,
Caliph Omar Moumin

Email:  [email protected] 



----- Original Message -----
From: Nick Cox <[email protected]>
To: "'[email protected]'" <[email protected]>
Cc: 
Sent: Tuesday, May 22, 2012 7:19 PM
Subject: RE: st: foreach command

Ronan's really answered his own question. As you can insert all kinds of stuff inside the loop, the looping command doesn't need an option to decorate each iteration of output. You can just provide your own decoration in exactly the way you want. 

In fact, there is a second kind of answer, or so I guess. In providing -foreach- and -forvalues- StataCorp were providing fairly standard kinds of looping commands recognisable to programmers with backgrounds in many kinds of languages, and there was no need to make them too quirky or add all kinds of extra syntax as icing on the cake. 

Nick 
[email protected] 


-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Ronan Conroy
Sent: 22 May 2012 18:00
To: [email protected]
Subject: Re: st: foreach command

On 2012 Beal 22, at 17:13, Caliph Omar Moumin wrote:

> I wanted to regress a data with many categories so i used this command
>  by subchapter2, sort: xtreg cost duration sex agegroup group, re robust
>  
> the problem is this command does not accept xi: command to change the var 'agegroup' into dummy variable
>  
> then i try to use foreach command, and i appplied it like this
>  foreach subchapter2_value in 1 2 3 4 5 6 7 8 9 10 11 {
> xi: xtreg cost duration sex i.agegroup group if subchapter2== `subchapter2_value', re robust
> }
>  
>  
> Now the problem is i cannot see the label name in the later case

This is a nuisance. The solution I adopt is

foreach subchapter2_value in 1 2 3 4 5 6 7 8 9 10 11 {
di "*================================================*"
di "* Results for Subchapter `subchapter2_value'     *
di "*================================================*"
di
di
xi: xtreg cost duration sex i.agegroup group if subchapter2== `subchapter2_value', re robust
}

This prints an old-fashioned ASCII banner in the output. However, I miss the option to echo the command during execution, as happened with the now-deprecated -for-

Ronán Conroy
[email protected]
Associate Professor
Division of Population Health Sciences
Royal College of Surgeons in Ireland
Beaux Lane House
Dublin 2


*
*   For searches and help try:
*  http://www.stata.com/help.cgi?searchhttp://www.stata.com/support/statalist/faqhttp://www.ats.ucla.edu/stat/stata/

*
*   For searches and help try:
*  http://www.stata.com/help.cgi?searchhttp://www.stata.com/support/statalist/faqhttp://www.ats.ucla.edu/stat/stata/


*
*   For searches and help try:
*   http://www.stata.com/help.cgi?search
*   http://www.stata.com/support/statalist/faq
*   http://www.ats.ucla.edu/stat/stata/


© Copyright 1996–2018 StataCorp LLC   |   Terms of use   |   Privacy   |   Contact us   |   Site index