Bookmark and Share

Notice: On March 31, it was announced that Statalist is moving from an email list to a forum. The old list will shut down at the end of May, and its replacement, statalist.org is already up and running.


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: st: AW: summary table after tab1


From   "Martin Weiss" <martin.weiss1@gmx.de>
To   <statalist@hsphsun2.harvard.edu>
Subject   RE: st: AW: summary table after tab1
Date   Sun, 27 Jun 2010 22:05:21 +0200

<>

-stack- the vars while -preserve-ing:

***********
clear*

input byte var1  var2 var3
1        4        2
3        1        6
6        1        5
2        3        4
6        4        5
end

preserve
 stack var?, into(myvar) clear
 ta myvar
restore

***********


HTH
Martin

-----Original Message-----
From: owner-statalist@hsphsun2.harvard.edu
[mailto:owner-statalist@hsphsun2.harvard.edu] On Behalf Of Andrzej Niemierko
Sent: Sonntag, 27. Juni 2010 21:45
To: Stata
Subject: Re: st: AW: summary table after tab1

Thank you Martin and Don. Unfortunately, that's not what I need.
Let's say I have three variables var1-var3 and they contain integer numbers
between 1 and 6, e.g.:

var1    var2    var3
1        4        2
3        1        6
6        1        5
2        3        4
6        4        5

-tab1 var*- gives me three tables of frequencies for each variable
separately. I need just one table that tells me the overall number of 1's,
2's, 3's etc.
Andrzej




On 6/27/10 1:13 PM, "Martin Weiss" <martin.weiss1@gmx.de> wrote:

> 
> <> 
> 
> You may want to use -egen, group()- beforehand:
> 
> 
> *************
> sysuse auto, clear
> tab1 turn trunk, sort
> egen mygroups=group(turn trunk), label
> ta mygroups
> *************
> 
> 
> 
> HTH
> Martin
> 
> 
> -----Ursprüngliche Nachricht-----
> Von: owner-statalist@hsphsun2.harvard.edu
> [mailto:owner-statalist@hsphsun2.harvard.edu] Im Auftrag von Andrzej
> Niemierko
> Gesendet: Sonntag, 27. Juni 2010 18:13
> An: Stata
> Betreff: st: summary table after tab1
> 
> What's the simples way to generate a one-way summary table of frequencies
> over several variables. -tab1 varlist, sort- generates individual tables
but
> I need a single table with frequencies summed over varlist.
> Thank you,
> Andrzej
> 
> 
> 
> 
> The information in this e-mail is intended only for the person to whom it
is
> addressed. If you believe this e-mail was sent to you in error and the
> e-mail
> contains patient information, please contact the Partners Compliance
> HelpLine at
> http://www.partners.org/complianceline . If the e-mail was sent to you in
> error
> but does not contain patient information, please contact the sender and
> properly
> dispose of the e-mail.
> 
> *
> *   For searches and help try:
> *   http://www.stata.com/help.cgi?search
> *   http://www.stata.com/support/statalist/faq
> *   http://www.ats.ucla.edu/stat/stata/
> 
> 
> *
> *   For searches and help try:
> *   http://www.stata.com/help.cgi?search
> *   http://www.stata.com/support/statalist/faq
> *   http://www.ats.ucla.edu/stat/stata/


*
*   For searches and help try:
*   http://www.stata.com/help.cgi?search
*   http://www.stata.com/support/statalist/faq
*   http://www.ats.ucla.edu/stat/stata/


*
*   For searches and help try:
*   http://www.stata.com/help.cgi?search
*   http://www.stata.com/support/statalist/faq
*   http://www.ats.ucla.edu/stat/stata/


© Copyright 1996–2014 StataCorp LP   |   Terms of use   |   Privacy   |   Contact us   |   Site index